Now repeat with the polishing stone.Īfter you’ve finished with both stones, repeat the entire process with the other set of blades. Once you’ve done this, use a soft cloth to wipe the loose metal from the blades and dry them. You should see the blades pushing a thin layer of water from one end of the stone to the other. Spray the stone with more water as it becomes dry. Repeat this procedure 10-15 times, or until the blade tips are shiny and you can see newly exposed metal. Once you get to the end of the stone, pick the blade up and start over at the opposite end where you started. Maintain that even pressure as you slide the blade from one end of the stone to the other, lengthwise. If you chose to use a magnet, you can use it to hold the blades, otherwise hold the blade down with your fingers. Place one of the blades flat against the coarser 4000 grit stone, with the edge of the blades on the stone. Step Five: Sharpen the Blades Using the Coarse Stone You should be able to spray water onto the stone and be left with a thin sheen of water on top. This lubricates the stone and allows it to function properly. Step Four: Prepare Your Whetstonesīoth stones should be allowed to soak for several minutes to absorb water. You should also check this is safe for the model of clipper you’re using. If you want to do this the quick way, you can simply leave the clipper blades attached and then submerge them in cleaning solution and turn them on for twenty or so seconds, but this may not get all the rust off. Gently pat the blades dry, leaving some of the solution on the blades to air dry. For more severely dirty blades that have been neglected, or just seen hard use, you may want to soak the blades in a small container of cleaning solution for a few hours. Rust, hair, and other gunk can build up on your clipper blades and make them difficult to use.įor mildly dirty blades, a simple scrub with a rag or cotton ball soaked in cleaning solution should be perfectly adequate. Step Three: Use a Cleaning Solution to Clean the Blades It’s very important that the blades remain clean and dry during the sharpening process so that they sharpen evenly. You can also brush hair out of the head of the clippers. Using either the supplied brush or other small brush (such as a toothbrush or cheap paint brush,) remove all the little pieces of fur from the nooks and crannies of the blades. You should now have one larger set of stationary blades, and a smaller set of reciprocating blades that sit inside the exterior blades. Once you’ve removed the blades, set your clippers aside for the time being. Other clippers may have a simple latch with a button to push, or a catch to flip open. Don’t lose these! I find it easiest to place them in a small bowl or something similar so they don’t roll off the counter and disappear forever. Typically, this is done by removing one to two screws holding the clippers down. įirst, make sure the clippers are unplugged, or powered off if you have a cordless model. Note: Looking for some new clippers? Check out our list of the best options at. Clipper oil: Oil is vital, as it lubricates the blades and helps prevent rust.Use a cleaning solution from any of the major clipper manufacturers (Oster, Wahl, Andis etc) that is designed specifically for cleaning clippers. Clipper cleaning solution: Solution is used for cleaning and derusting the clipper blades.Soft cloth: This is useful for removing bits of metal taken off by the sharpening stones.Spray bottle of water: The most common sharpening stones are “water stones” that need to be wet in order to work properly.If you have ceramic clipper blades, you’ll need diamond coated stones. Some will have a coarse and a fine side so you only need to buy one stone. You can commonly find these online, or at your local hardware store. Whetstones: You’ll need two stones, one of a coarse grit in the 3000-4000 grit range, and a finer grit stone around 8000 grit.Screwdriver: Most clipper blades are held with one or two Phillips head screws.Clippers: First, you’ll need your clippers, and their instructions, or at least the knowledge of how to remove the blades from the body of the clippers.While proper maintenance can keep your clippers working for quite a while, eventually you’re going to need to sharpen the blades. Unfortunately, trying to groom your dog with dull clippers can be frustrating at best, and unsafe at worst. Keeping your dog’s hair trimmed isn’t just important for aesthetic reasons, but also for their health and safety. Step Seven: Reassemble the Clippers and Test.Step Five: Sharpen the Blades Using the Coarse Stone.Step Three: Use a Cleaning Solution to Clean the Blades.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |